Owens Corning Flashing Replacement Nationwide

Owens Corning Flashing Replacement: The Orlando Owner’s Guide

Owens Corning flashing replacement in Orlando typically runs $380 to $900 installed, depending on which flashing point failed and how much decking repair is needed around it. We stock Owens Corning-compatible flashing on our trucks, and most replacements are done in a single visit. The way most Orlando homeowners find out their flashing is gone: a brown stain spreading across the ceiling after an afternoon thunderstorm, or granules collecting in the gutter below a valley that should be shedding water cleanly.

Call (448) 218-0800

The flashing is the metal transition piece where the roof meets something vertical, like a chimney, a skylight, a wall, or a vent pipe. When Owens Corning shingles are installed correctly, the flashing is what keeps the water from sneaking in at those joints. When it fails, the shingles above it can be in perfect shape and you’ll still get a leak. That confuses a lot of people. They look up at the shingles and they look fine. The problem is underneath or alongside them.

Which Owens Corning Models This Applies To

Flashing is not shingle-specific, which is the first thing to understand. Whether your Orlando roof is wearing Owens Corning Duration, Oakridge, or Supreme, the flashing details are mostly the same: step flashing at walls, counter-flashing at chimneys, pipe boots at plumbing vents, and valley metal where two roof planes meet. What does differ is the profile of the flashing and how it’s lapped with the shingle course.

On Owens Corning Duration installations especially, the shingle’s larger exposure means step flashing pieces need to be a minimum of 4 inches high and 4 inches up the wall, with each piece lapping the next by at least 3 inches. We see a lot of Orlando roofs where someone used 2-inch or 3-inch step flashing with Duration shingles and the result is a leak that shows up within two or three wet seasons. The shingle is thicker and the water has a longer path, so short flashing gets overwhelmed.

We install OEM Owens Corning flashing where it matters, and quality aftermarket equivalents where the material spec is identical. Let’s be honest about what “OEM” means here: Owens Corning manufactures shingles and roofing accessories, but a lot of the flashing you’ll see labeled as Owens Corning is produced under license. The actual spec that matters is the gauge of the metal. In Central Florida, 26-gauge galvanized or aluminum is the floor for anything we install. Thinner than that and the afternoon thermal cycling plus humidity will eat it inside a decade.

If you’re trying to figure out which flashing you have now, check the edge of any exposed metal. The gauge is often stamped there. Older Orlando homes from the 1990s and 2000s frequently have 28-gauge or 30-gauge flashing, which is why so many roofs from that era are leaking at the same age.

Signs Your Owens Corning Flashing Replacement Is Failing

• Ceiling stains near a wall or chimney, not the middle of the room. Water that gets past flashing travels down a stud or along a rafter before it shows up, so the stain often appears where the wall meets the ceiling, not directly under the roof leak. The actual entry point can be 6 to 10 feet away.
• Granules from Owens Corning shingles collecting in a gutter at a valley or wall line. When flashing fails, water runs under the shingle edge and scours the asphalt coating. The shingles themselves are not the failure point, they’re being damaged by the water the flashing was supposed to stop.
• Lifted or curling shingle edges right next to a wall or chimney. This is often the flashing telegraphing through. The metal underneath has warped from heat cycling, and it pushes the shingle edge up so wind can catch it. In Orlando’s June through September heat, a poorly installed flashing piece can warp enough to visibly lift a shingle within two summers.
• Rust streaks down the side of a chimney or wall. Galvanized flashing eventually gives up its zinc coating, especially in Orlando’s humidity. The rust staining on the stucco or brick is the visible part; what you can’t see is the pinhole corrosion behind it that lets water through.
• Damp attic insulation or water staining on the roof deck only in isolated spots. A widespread leak usually means the roof system has broadly failed. A single wet spot at a plumbing vent or wall intersection is almost always flashing-specific.

Replacement Cost & What’s Included

For an Owens Corning flashing replacement in Orlando, most homeowners pay between $380 and $900 installed. A simple pipe boot replacement at a plumbing vent runs at the low end. Step flashing along a wall or dormer runs $450 to $700 depending on how many courses are involved. Chimney flashing with new counter-flashing and a proper reglet cut into the mortar is typically $700 to $900. If the roof decking around the failed flashing is rotted from prolonged exposure, that repair adds $80 to $150 per sheet of plywood replaced.

The number you get from us is the number on the invoice. We itemize the flashing material, the fasteners, the sealant, and the labor separately, so you can see exactly what you’re paying for. That’s how Dylan Pace has run Crestview from the beginning: no lump-sum “roof repair” line hiding a mystery number. You’ll get a written price before we touch anything, and every flashing replacement is covered by our 365-Day Done Right Promise. If it leaks within a year, we come back and fix it at no charge.

DIY or Call Us?

You can safely inspect a lot of this from the ground with a pair of binoculars. Look for lifted shingle edges at wall lines, rust at chimney bases, and pipe boots that look cracked or pulled away from the pipe. What you should not attempt yourself is pulling up Owens Corning shingles to access flashing. The sealant bond on Duration shingles is aggressive, and if you bend a shingle too far, it cracks and you’ve turned a $500 flashing job into a $1,200 flashing-plus-shimmy-and-replace job. The self-sealing adhesive on Owens Corning’s laminate line is not DIY-friendly to re-set.

Roof work on a two-story Orlando home with a 6/12 pitch is not where you want to learn about fall protection. We do this with proper harnesses and a crew that knows the difference between a repair and a liability. If you want to know what you’re looking at before anyone climbs up, call (448) 218-0800 and we’ll talk you through it. Estimates are free, and the person who answers is a live human, not a call service.

FAQs